(0) Cart
  • No products in the cart.


BlogHome »

FVT LittleBee 20A (MRM ZEUS 20) VS KISS 18A ESC

The new “Favorite” FVT LittleBee 20a arrived into the HacksMods lab. So it’s time to take some clear shots of them and compare with the Flyduino KISS ESC. Which is still one of the highest performing multirotor electronic speed controller. The small size and light weight are great for putting on racing quads. Or burying inside heavier aerial photography equipped quadcopters, or “drones” as the media likes to call it.

In the USA, the Little Bee 20a are known as the MRM Zeus 20. Brian (punkindrublik on RCGroups) of  MultiRotorMania help finance and brought these new ESC to market. So they secured the rights as the sole distributor in the USA. However, the ESC should soon be available from some of your favorite multi rotor online stores.

Continuing in the same small by mighty form factor that the Flyduino KISS ESC brought to market, the FVT LittleBee 20 are about the same size. 12.5mm x 23mm x 3mm. Versus the KISS (v1.1) 12mm x 24mm x 3.81mm

What makes these new FVT LittleBee the current popular ESC is that recent test are showing them to perform similar to the KISS ESC. (Here’s one by QuadMcFly) This is in part due to the use of the SilLab F330 MCU. Which has a faster clock speed than the popular ATMEL chip used on most competing ESC. Add to that dedicated FET drivers and it’s performing quite well. This is what BLHeli creator Steffen has to say about it:

Then there is a very promising little ESC, the FVT Littlebee 20A:

This ESC has a good design with fast dedicated driver chips, which gives excellent freewheeling and exceptional braking.

Initial stress testing on 4S with a Cobra 2208/2000 with 6×4.5 prop, doing repetitive immediate accelerations from low rpm to full throttle went well.
During the initial acceleration, this setup pulls about 100A, so it’s a tough test for a small ESC (and can break other small ESCs).
Hopefully this indicates that the ESC will prove to be a reliable performer.

And so far, this is the closest performer to KISS that I have seen in this size.

Very clean layout and manufacturing placement of components on the PCB. Definitely KISS quality for sure. It seems like they used higher temp lead free solder. My Metcal MX500 soldering station usually makes quick work with lead free solder. But I admit, it took a split second longer with the solder joints on these Little Bee 20. This may be to prevent overheated MOSFET from desoldering itself like what appears the DYS SN20a are doing in some of the recent batches. Also, keep in mind that having to flow the solder at a higher temp usually slows down the manufacturing process. This, along with how clean the ESC looks and components are laid out…continue to signify a high level of quality control. So kudos to Favorite and MultiRotorMania.

favorite_FVT_littlebee_opto_20a_mrm_zeus_20_closeup_sidebysidefavorite_FVT_littlebee_opto_20a_mrm_zeus_20_macro_signal_wire_side favorite_FVT_littlebee_opto_20a_mrm_zeus_20_macro_mosfet_side

Weight of the FVT LittleBee 20a as it came out of the package is 6.73g.

Weight of the FVT LittleBee 20a without heatshrink and wires is 2.12g. I know some of you guys want to know things like this. I know as a hobbyist, I do. So very similar to the KISS 18a which I weighed here. And about .70 grams heavier than the ZTW Spider 18a Opto Lite.

Signal wire polarity in case someone needs this info in the future. (That’s would usually be me.)favorite_FVT_littlebee_opto_20a_mrm_zeus_20_amp_polarity

I have a few new frames I’d like to use these LittleBee on. Can’t wait to see them fly.

Some of my favorite places to buy from that carries these FVT LittleBee/MRM Zeus 20:
MultiRotorMania: MRM Zeus 20 Amp ESC
BangGood: FVT LittleBee 20 Amp ESC

BoltRC: Little Bee 20A ESC

BangGood: FVT LittleBee 20 Amp ESC
MyRCMart: RCX 20A (Little Bee) Mini BLHeli Multirotor ESC

MultirotorParts: Favourite Littlebee 20A
Supreme FPV: Littlebee 20a esc 2-4s

More info can be found on RC Groups discussion thread:
Little Bee and MRM Zeus 20AMP ESC’s

Leave a comment →

ZMR 250 Lite Build

daryoon_zmr250_flight_controller_access_hatch daryoon_zmr250_flight_controller_programming_header daryoon_zmr250_fpv_pod daryoon_zmr250_fpv_pod_front daryoon_zmr250_fpv_pod_front_angled1 daryoon_zmr250_fpv_pod_fronttop_angled

daryoon_zmr250_fpv_pod_tilt daryoon_zmr250_lipo_battery_connector_and_distribution_center  Dimon372_599791_zmr250_bumper_big_side_shielding  ZMR250_KISSPDB_KISS_ESC Daryoon_ZMRLite_250_LED_inside_afromini_amaze Daryoon_ZMRLite_250_FrSky_X4R-SB ZMR250_KISSPDB_SN20a_ESC

Alternate configuration with the battery plate. Allows more space to hide things.

Categories: Builds, Uncategorized
19 Comments on ZMR 250 Lite Build